Melin Herramienta A-L Cobalto Acero Cuadrada Nose End Mills, pulgada, longitud de largo, vástago Weldon, Uncoated (acabado brillante), 30Grado

Descripción
The Melin Tool A-L-series uncoated (bright) cobalt steel long-length square nose end mill has two flutes, a center-cutting design, and a 30-degree helix angle for general-purpose machining on most medium-hardness and tough materials, including stainless steel, nickel-based alloys, brass, and iron. Long-length end mills have longer cutting edges than medium-length end mills for applications with a high depth of cut. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high cutting depth. The tool’s square end creates sharp, unrounded cuts. The center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit. The 30-degree helix angle supports general-purpose applications. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action. Cobalt steel can be run at faster speeds and stays sharp longer than high-speed steel tools, while offering resistance to heat and abrasion. With no coating or surface treatment, this uncoated tool can be used on a range of materials. Cutting diameter tolerance is + 0.0015 to – 0.000″. This tool has a Weldon shank. End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. If heat is not reduced effectively, the tool’s cutting edges will dull and additional material buildup can occur. The number of flutes can range from two to eight. Two-flute designs offer the most efficient chip removal, but more flutes provide a smoother finish. The shank is the end of the tool held in place by a tool holder or machine. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts. Melin Tool manufactures cutting tools such as end mills, countersinks, drills, and thread mills. The company, founded in 1940, is headquartered in Cleveland, OH.
Características
Adecuado para uso general en la mayoría de mecanizado de dureza media y resistente materiales, incluyendo acero inoxidable, aleaciones de nickel-based, latón, y hierro Dos copas ofrecen una mejor chip-carrying de capacidad que molinos finales con más copas, mejorar la capacidad de quitar materiales de la herramienta long-length extremo Mills tienen mayor y bordes de corte puede hacer más corta que medium-length extremo Mills Resiste abrasión y temperaturas altas de corte, y que tiene mayor tasa de alimentación de broca de acero de cobalto Sin revestimiento (brillante) herramientas no tienen tratamiento de superficie o revestimiento adicional para el uso en una variedad de materiales
El número de Modelo (ItemModelNumber)
10506
Peso
8.80 Onzas
Dimensiones
5.4 x 0.8 x 0.8 pulgadas
Fabricante es Melin Tool Company
Destacados
Adecuado para uso general en la mayoría de mecanizado de dureza media y resistente materiales, incluyendo acero inoxidable, aleaciones de nickel-based, latón, y hierro, Dos copas ofrecen una mejor chip-carrying de capacidad que molinos finales con más copas, mejorar la capacidad de quitar materiales de la herramienta, long-length extremo Mills tienen mayor y bordes de corte puede hacer más corta que medium-length extremo Mills, Resiste abrasión y temperaturas altas de corte, y que tiene mayor tasa de alimentación de broca de acero de cobalto, Sin revestimiento (brillante) herramientas no tienen tratamiento de superficie o revestimiento adicional para el uso en una variedad de materiales